Showing posts with label cable chick. Show all posts
Showing posts with label cable chick. Show all posts

Saturday, September 21, 2013

Cisco Based Networking Questions part xii

Strive not to be a success, but rather to be of value. 
–Albert Einstein.

More Random Cisco Based networking Questions for you to ponder.

1, In a local broadcast all bits set to 1 received by all hosts on local and remote broadcast domains?

A) True
B) False


2. Which protocol is used to determine the IP address if the MAC address is already known?

A) ARP
B) RARP
C) IP
D) IPX
E) TCP


3. What is the invalid timer set to by default when you have a router running the Interior Gateway Routing Protocol?

A) 3 times the update period
B) 270 seconds
C) 3 times the update period + 10 seconds
D) Answer A and B
E) 7 times the update period


4. The startup-config (Cisco) is found in the ...

A) FLASH
B) DRAM
C) NVRAM
D) ROM


5. What component of a router holds the routing tables and the software that allows the router to function?

A) Bootstrap
B) POST
C) ROM monitor
D) RAM
E) Configuration register


6. Which switching mode has the highest degree of error checking?

A) Fragment-Free
B) Fast-Forward
C) Cut-Through
D) Store-and-Forward
E) FIFO





1. Correct Answer: B
Routers don't forward broadcasts so local broadcasts will stay on the broadcast domain from which they originated.


2. Correct Answer: B
Reverse Address Resolution Protocol (RARP) is a networking protocol used by a host computer to request its IP address from an administrative host, when it knows its MAC address.


3. Correct Answer: D
IGRP sends its routing table to its neighbors every 90 seconds. IGRP uses an invalid timer to mark a route as invalid after 270 seconds (three times the update timer). IGRP uses a flush timer to remove a route from the routing table (default flush timer is 630 seconds, seven times the update period).


4. Correct Answer: C
The startup configuration is stored in NVRAM


5. Correct Answer: D
The running-config is stored in RAM and allows the router to function.


6. Correct Answer: D
Store and forward switching method is known as store and forward because the switch will store the incoming data frame in its internal buffer, then when the complete frame has been received the switch will then run a Cyclic Redundancy Check (CRC) against the frame. If the CRC passes, the switch will then look up the destination MAC Address in its MAC filter table to forward it on to its destination.


More to come - stay tuned...

Friday, May 10, 2013

How TCP and UDP work



Transmission Control Protocol (TCP) and User Datagram Protocol (UDP)is a transportation protocol that is one of the core protocols of the Internet protocol suite. Both TCP and UDP work at transport layer TCP/IP model and both have very different usage.




Lets imagine, that we need to transfer certain amount of data. You may transfer only certain amount at the time (you have limitation on the packet size, which is below TCP/UDP).

In case of TCP, first you should establish connection (you may read about "3-Way handshake"). During this you agree on the "TCP Window Size" (explained  below). Then you start actual data transfer...

You transfer a packet, and then you wait for a confirmation, that the packet received. If you didn't receive confirmation within certain amount of time, you transmit the same packet again (Retransmission occured). If you agreed on certain "TCP Window Size", you may transmit multiple packets without waiting for a confirmation, and then you receive one confirmation for all these packets (not many, usually a few, just "more than one"). If you sent 3 packets, but only two confirmed, you will send that missing packet, if no confirmation was received at all, then you send all 3 packets again. But the bottom line is - each and every packet should be confirmed.

TCP has tweaked for performance over the years. ACKs are often piggy-backed with replies to messages so there is no extra packet or waiting. It can also dynamically adjust to changing network performance with features like slow start and congestion avoidance. TCP optimizes the amount of data sent per packet to avoid IP fragmentation. With UDP, if you send a message greater than 1472 bytes (for 'normal' Ethernet) the IP layer will fragment it into multiple datagrams and it will buffered and re-assembled in the receiving stack.


In case of UDP, you just blindly split your data into packets, and transfer them without any care, if they were received or not. You may do it "at the wire speed". And if you need some kind of control over the data, this should be taken care on higher layers of OSI model (for example, you should implement transfer verification at the Application Layer).


So, in theory, TCP actual performance is at least twice slower (for example, your one-way-trip time is 100ms, you sent a packet, and wait for a response), plus depends on receiver (how long it takes to prepare and send a confirmation), while UDP may send packets "as a stream" without any delay.

That said, there are many case where UDP may be a better choice. there isn't much use for retransmissions with applications like VOIP. For a simple exchange where you don't need the overhead of establishing and tearing down a connection UDP is likely the way to go, DNS being a perfect example. Note that even DNS will switch to TCP when the server sees that the reply will be lengthy due to multiple addresses and/or MX records.

If you are creating a VoIP application, there is no need constantly to check if the other end is on-line, so you can use UDP to transfer the main payload (voice) and a second TCP connection to handle connection/disconnection at a lower speed (once a second is ok).

If you are transmitting a public radio station over IP, you need only to enable your players to join one multicast channel. In the latest case, UDP is far more effective and is causing less overhead, since all the network balancing is handled by the multicast enabled routers.

In areas of video streaming and VoIP the overhead of TCP would be intolerable, so they use UDP and they work pretty well- mainly because the network infrastructure and the protocols have "matured" to the extent where reliability is largely taken for granted.



Clear as mud?



Monday, April 1, 2013

CCNA exam questions part vii

The following is a selection of exam type questions for computer networking, specifically pointed toward CCNA certification.  Good to get the grey matter clicking as a refresher as well, enjoy!


 1. Inter-Switch Link and IEEE 802.1Q are types of...

A.) Spanning Tree Protocol
B.) Trunking method
C.) Ethernet
D.) Routing protocol


2. What is port 53 used for?

A.) FTP data
B.) FTP program
C.) Telnet
D.) DNS
E.) TFTP


3. Frame tagging is used to identify...

A.) The intended recipient of a frame
B.) The IP address of the frame
C.) The source of the frame
D.) The VLAN ID of the frame
E.) The trunking method


4. Where is the start-up configuration file held in a (Cisco) router?

A.) NVRAM
B.) RAM
C.) Routing table
D.) ROM

5. A CIDR value of /30 equates to what subnet mask?

A.) 255.255.255.253
B.) 255.255.255.128
C.) 255.255.255.248
D.) 255.255.255.252


6. Where would you place standard access lists?

A.) As close to the destination as possible
B.) As close to the source as possible




-->
Clickbank Products


1. Answer B

2. Answer D

3. Answer D
 
Explanation: Frame tagging is used to tags frames on trunked links to identify what VLAN they belong to.


4. Answer A

5. Answer D

6. Answer A

Explanation: Standard access lists only filter based on source address so they have to be placed as close to the destination as possible.


Creative | Australian Online Store

Monday, March 25, 2013

CCNA networking quick questions

Another random assortment of Cisco based networking questions you can use as a primer for achieving CCNA certification or as a refresher.  

Scroll to the bottom for examination tips .. 

1.  How many IP access lists can you assign on an outbound interface?

A.) 1
B.) 1-100
C.) Unlimited


2. What type of switch port can belong to multiple VLANS?

A.) Access port
B.) Trunk port
C.) Voice access port
D.) No port can belong to multiple VLANs


3. What happens if a packet does not match any of the ACL statements?

A.) Nothing
B.) It is rejected
C.) It is allowed


4. Protocol Data Units of the Physical layer are called?

A.) Bits
B.) Frames
C.) Segments
D.) Packets


5. Bridges can only have one spanning tree instance, while switches can have many.

A.) True
B.) False









1.  Correct Answer A

2.  Correct Answer B

3.  Correct Answer B

4.  Correct Answer A

The Layer 1 (Physical Layer) PDU is the bit
The Layer 2 (Data Link Layer) PDU is the frame
The Layer 3 (Network Layer) PDU is the packet
The Layer 4 (Transport Layer) PDU is the segment


5.  Correct Answer A




Here are some revision tips to help you revise for the CCNA exam, or any Cisco exam for that matter...

1.)  Make sure you only learn topics which are covered by the exam.
2.)  Glance through the course/exam topics and highlight the areas you think you'll need to concentrate on more.
3.)  Get a good CCNA book that suits your learning style.
4.)  Practice what you learn frequently by using practice tests and flash cards. Highlight your weakest subjects and aim to improve them.
5.)  Create a set of revision notes for each topic. Try to stick to one page of paper per topic.
6.)  Read through your revision notes frequently.
7.)  You want to retain the information beyond the exam, so forget about cramming the night before the exam. Spread out your revision into 30 minute revision periods.
8.)  Condense your revision notes. The act of rewriting them will help you memorize them.
9.)  Practice your IOS configuration on a Cisco router or router simulator.

Saturday, February 2, 2013

Star fleet engineering


Gives you a headache doesn't it, maybe IKEA can get some tips :-)




I failed a Health and Safety course at the office yesterday. 
One of the questions was: "In the event of a fire, what steps would you take?" 

"F*%king' big ones" was apparently the wrong answer.